Category: Eclectic Homes

How Hard Is It to Change the Roller on a Pella Door?

The rollers to get a Pella sliding door fit within rectangular metallic cartridges, and these cartridges in turn fit into mortises at the bottom of the doorway. When correctly installed and functioning, the grooved roller matches on the knee monitor and glides smoothly, but during age and regular use, the roller might get bent, chipped or otherwise damaged and require replacing. To do it, you have to pull the metallic cartridge out of the doorway, which takes a special corkscrew-style tool. In case you have the instrument, the job is simple, but without it, then some frustration might be involved.

Prepare the sliding half of this doorway for removal. The procedure differs , based on the collection. For doors at the Architect or Designer collection, you have to remove the panel retainer screw at the bottom of the door that holds the door to the track. For doors at the ProLIne series, remove the handle and masonry at the top monitor, with a screwdriver.

Lower the bearings by turning the screws at the bottom corners of the doorway counterclockwise to provide clearances, then lift the doorway and angle the underside away from the framework to eliminate it. Set the door to a pair of sawhorses.

Turn the roller adjustment screws clockwise as far as they will go to exposes the plastic rollers. Unclip each roller in the holder.

Remove the metallic cartridges by inserting the bolt of a corkscrew-style capsule puller through the holes that were holding the roller. Align the puller using the foundation of the door and tighten the screw to extract the capsule.

Extract the cartridges with a vise if you don’t have a puller. Set the door onto a workbench so that the underside is facing the vise and anchor it by screwing a wood brace against the underside.

Feed a length of 14-gauge wire through the holes that held the roller, then wrap the wire around the vise and pull it tight. Open or close the vise — based on the vise’s alignment, to extract the capsule.

Put in a brand new cartridge and roller by inserting the cartridge at the mortise and tapping it in with a hammer.

Lift the bearings by turning the adjustment screws clockwise before you reinstall the doorway.

See related

How to Put a Belt on a Craftsman FS5500 Riding Lawn Mower

During conventional mowing operations on an established lawn, the deck belt in your own Craftsman FS5500 riding mower usually lasts for two or three mowing seasons. But when mowing through bare locations, friction caused by flying dust, gravel and debris causes abnormal belt wear. Consequently, periodic belt checks are called for — and if it becomes necessary, replacing the belt requires under one hour.

Deck Removal

Park the mower on a firm flat surface. Turn off the engine and remove the ignition key. Set the parking brake, set the clutch lever at the “Disengaged” position and lower the attachment lift lever to its bottom position. Remove the spark plug wire from the spark plug and protected the wire safely away in the plug. Wear a pair of heavy work gloves.

Catch the forward-facing belt tension pole on the upper left of this mower deck. Maintain a firm grip, lever downward and push the end toward the tractor to disengage the spring-loaded rod in the port in the lock bracket. Once free, ease the end gradually upwards to release stress on the mower deck belt.

Go to the right of this mower. Reach underneath and remove the belt in the electrical clutch pulley situated in front of the deck.

Remove the retainer spring and washer by hand in the pin protruding through the hole at the front right suspension arm situated on the upper front of the deck, disengage the link. Repeat by disengaging the ideal rear lift link in the ideal lift arm bracket situated on the upper rear of the deck.

Disconnect the leading link between the deck and the mower chassis by removing the retainer washer and spring from the pin on the chassis and pulling the front of the link in the pin.

Remove the retainer washer and spring from the anti-sway bar connected to the perfect rear lift arm bracket. Pull the deck towards the right until the pub falls in the hole in the bracket.

Go to the other side of the mower and disengage the left front suspension arm and left rear lift arm exactly the same manner.

Turn the tractor steering wheel so that the wheels point all the way towards the left. Slide the mower deck out from below the ideal side of this tractor.

Belt Replacement

Remove the screws securing the two mandrel covers to the left and right of the deck using a Phillips screwdriver. Put the screws within the covers and lay them apart. Take note of this belt configuration and eliminate the old belt in most of drive and idler pulleys.

Remove all dirt and grass clippings from around the pulleys and the upper deck with a stiff-bristle brush.

Install the belt around the three mandrel pulleys with the “V” of this belt facing inward toward the pulley groves. Loop the horizontal side of the belt over both idler pulleys and feed the loose end of the belt forward towards the clutch pulley position.

Reinstall both outer mandrel covers and tighten the screws securely.

Deck Installation

Period the mower deck suspension arms towards the front. Slide the deck below the tractor and middle it front to back and side to side.

Reach under the perfect rear of the mower deck. Lift the anti-sway bar and insert the far end into the hole at the left transmission bracket. Pivot the pub towards the right, move the deck as needed, and insert the other end into the hole at the perfect rear suspension bracket.

Secure the anti-sway pub by replacing the washer and retainer spring removed before onto the end of this anti-sway bar protruding through the ideal suspension bracket.

Reinstall the front right suspension arm by sliding the port on the end over the pin protruding in the table and replacing the washer and retainer spring removed before. Reconnect the leading link and fasten it to the pin on the chassis with the washer and retainer spring removed before.

Go to the other side of the tractor and reinstall the left front suspension arm exactly the same manner.

Attach the perfect rear lift link by lifting the corner of the deck and positioning the port in the end of the link over the pin protruding from the rear lift arm bracket. Secure it with the washer and retainer spring removed before. Repeat and attach the left rear lift link exactly the same manner.

Slide the loose front part of this new belt over the electrical clutch pulley. Check the entire belt for proper alignment and navigation in all the pulley grooves.

Go to the left hand and push the belt tension rod down and then fasten it by hooking it in the slot in the lock bracket.

Lift the deck by raising the attachment lift lever to highest position to finish the installation.

See related

The Way to Tile Over Cracked Floors

There is A tile floor stable and only as robust as the subfloor where it’s installed. Cracks in concrete are a sign of a problem. Cracks mean motion, and a tile floor isn’t meant to move. Should you install vinyl then most probably, the crack will show up in the tile. To avoid a crack from forming in the tile, then you need to supply ways to permit a little bit of motion in the floor without transferring it.

Mix the mortar in accordance with package directions, replacing the water additive to give strength and flexibility to the mortar.

Cut strips of ceramic tape, made to protect joints in cement backer board, to fit over the crack. If the crack is directly, cut just one piece that is long. If the crack is jagged, cut the tape into smaller bits. The crack does not need to remain beneath the tape’s center so long as the crack wills span.

Force the thin-set to the crack using a trowel, filling the crack flush with the concrete. Smooth the mortar apartment with the flat edge of the trowel.

Place the pieces of tape you ready over the crack. Work in spans so you can complete all steps prior to the starts to set. The latex will also make the mortar to stiffen. Gently over the tape together with the flat edge of the trowel and push it into the thin-set onto the concrete’s surface.

Trowel mortar about the tape. Force the mortar till you’ve got an almost flat field of tape and mortar spanning the crack, and smooth it out again. Allow the mortar to set.

Sand over the tape using a rubbing stone, hammering the mortar and tape job and smoothing out any rough spots. A little or brick piece of cinder block also work. You’re now ready to tile the floor as ordinary.

See related

How Can I Convert an FHA Loan to a Regular Mortgage?

An FHA-insured loan is a conventional mortgage loan via an FHA-approved lender guaranteed by the Federal Housing Administration. The loan itself is not any different from any other consumer lending; the most notable difference is the procedure for procuring the loan. Nonetheless, homeowners that previously secured their mortgage loans through the FHA may later opt to convert their loan to a”regular” house loan. To convert an FHA loan to a conventional mortgage, you’ll need to refinance your current mortgage. The FHA must approve the refinance, even though you’re moving to some non-FHA-insured lender. The method is remarkably like a traditional refinance, even though there are a few extra considerations.

Find and study qualified mortgage lenders in your region. If you’re content with your current lender and current on your mortgage, this is a fantastic place to start. Also consider your local bank branch or credit union, as you’re likely to secure better terms as a recognized client. Consider larger, nationwide lenders over smaller, locale-specific institutions, as the former are usually in a better position to provide more competitive rates than the latter. Compile a list of your top three or four lenders for consideration.

Get in touch with the list of lenders you accumulated; schedule a meeting with a mortgage consultant at every branch, when possible. After you attend, bring along a list of your current earnings, assets and obligations; you don’t need to bring any records to substantiate your earnings at this time. Request a quotation from every lender, but don’t provide your sensitive info at this time. Don’t allow any creditor to pull your credit report until you opt for the lender with which you want to refinance.

Complete a formal application with the lender you choose, and provide copies of your last two pay stubs, latest income tax return, statements of your personal assets (including savings account, stocks or other investments), a listing of your recurring monthly obligations (including utility bills and insurance premiums), a listing of your current outstanding loans and corresponding creditors as well as the name to your house. You might also need to provide photographic identification and your Social Security card to substantiate your identity.

Consult with an independent house appraiser to conduct an assessment of your house. The lender may require you to pick from a list of approved appraisers, but the appraisal will be at your expense. Give the lender with a copy of the appraiser’s final report as soon as possible.

Attend your final. This is very much like the final you attend if you purchased your home. If you opted to get a”no closing cost” refinance, you will not incur any extra fees at closing (although you will recognize these fees at the end of your repayment term). Otherwise, be ready to cover the closing costs in cash at this time. Assess and re-check the terms of your refinanced mortgage–the interest type and rate, specifically–until you sign the bottom line. The creditor can alter the interest rates at any time before closing, and some lenders will raise the interest rate without notifying you. You’re locked in at the rate presented on the arrangement unless and until you refinance once you sign.

Pay off your FHA-insured loan as soon as your new creditor disperses the money. Your new lender will not, by default, put on the balance of your refinanced loan to your original mortgage. You’ll need to do yourself, right to your original lender.

See related

Turn a Shipping Pallet Into a Stylish Ottoman

A low-slung upholstered ottoman is an easy, budget-friendly and high-impact DIY upholstery job. And because you create it yourself, it is completely customizable.

The first thing you’ll need for this job is really a frame. Retrofitting a shipping pallet works perfectly. When you’re delighted with your selection of a pallet, it is time to get to work creating your one-of-a-kind upholstered ottoman. It’s simpler than it seems — all you’ll need are a couple of supplies and a very basic knowledge of sewing and woodworking.

Watch out! If your friends find out the way you made it, then they will want to purchase yours or have you create one for them.

Upholstery Club’s Shelly Leer

You would never think this was a shipping pallet, right? A mixture of textured chartreuse fabric, dressmaker detailed gray velvet buttons and silver-tipped contemporary legs signifies this ottoman will take centre stage in almost any home or studio.

Materials required:
A secure pallet (read for hints on choosing a single)Enough 1-by-4 Parts of straight boards to attach to the bottom borders of your palletDrill (pieces and Phillips head chuck)11/2 -inch wood screwsStaple gun (preferably electrical)Electric knife (to cut foam)ScissorsBurlap or scrap fabric2-inch-thick foamDacron batting2 yards of fabricCovered buttonsNeedle and thread (optional)Legs and attaching hardware

Upholstery Club’s Shelly Leer

First, let us address some concerns you might have about utilizing flashlights. Not all pallets are made equally. I’d suggest using non-chemically treated, new, dry, un-weathered pallets for this frame. If you still have concerns of using a pallet, it is possible to easily construct the exact same simple frame from scrap wood.

If you do choose to use a pallet, steer clear of anything with an HT or MB stamp. These indicate heat treatment (possibly with compounds) or methyl bromide treatment. The pallet I used here has no marks, so it appears like new wood and it is a smaller dictionary, occasionally called a quarter-pallet. I got mine from a kitchen cabinet distributor beside my shop, but it is possible to find new pallets on the internet for under $20.

Pallets can have powerful threaded nails in them, too. Make sure you’re aware of all nails before cutting into a pallet.

Upholstery Club’s Shelly Leer

Measure, cut and attach 1-by-4 parts of wood to the underside edge of the pallet.

Upholstery Club’s Shelly Leer

Quantify and attach leg hardware. You are able to add a dust cap to the bottom of the ottoman after it is upholstered; it’s no problem to find the holes in the leg plates.

Upholstery Club’s Shelly Leer

Put the frame in addition to a piece of 2-inch-thick foam. Trace across the top edge with a marker and use an electric knife to cut out the piece of foam.

Upholstery Club’s Shelly Leer

Measure and cut burlap or scrap fabric to shut in the frame. Safe with shovel or spray adhesive.

Upholstery Club’s Shelly Leer

When the frame is wrapped in burlap, add spray adhesive to ensure the centered foam to the top of the frame.

Upholstery Club’s Shelly Leer

Here’s the foam connected to the burlap-covered frame.

Upholstery Club’s Shelly Leer

Measure and cut cotton Dacron to cover the top and sides of this ottoman frame. Don’t wrap the Dacron below the frame. Use spray adhesive or staples to secure the Dacron set up, but stop at the bottom edge. Again, do not wrap the Dacron below the frame!

Upholstery Club’s Shelly Leer

Measure, cut and attach top fabric to the ottoman frame. It’s important to keep the fabric grain straight here. Secure 1 side of the fabric below the frame at the center, then move out toward the corners. Staple a bit at a time, then move to the other hand, pulling firmly and evenly and out toward the corners. (This pulls out lumps and bumps.) Secure each side with a line of basics, moving out toward the corners but stopping at 6 inches brief of every corner.

Upholstery Club’s Shelly Leer

Here’s where you want to be kind of convenient. The corners are completed like tidy hospital corners, except you are able to cut and eliminate a number of those tight fabric under the corner folds. Be careful not to cut out any top fabric. Pull 1 side across the corner edge, pulling slightly down and on the diagonal. Secure with principles.

Upholstery Club’s Shelly Leer

To fill in the staple dimples, put a small bit of poly fill on the principles.

Upholstery Club’s Shelly Leer

See? A perfectly smooth finish. It’s possible to screw the legs into the plates or wait till the dust cap is on the bottom. I used a few of my custom-designed thighs, but it is possible to find unique styles elsewhere on the internet.

Upholstery Club’s Shelly Leer

If you would like to sew the corner closed, then utilize an upholsterer’s sew (ladder) or an invisible stitch. Another choice is carefully running a small bead of hot glue within the fold and then pressing on the fold right into position.

Upholstery Club’s Shelly Leer

It can be difficult to put buttons evenly, so I cheated. Instead of attaching the buttons with a nail back or hand stitching them into position, I used a template, then marked the button placement with chalk and subsequently made an “X” with two principles where the coated buttons will be glued into position.

Upholstery Club’s Shelly Leer

This dressmaker detail about the corners adds a bulge of sophistication to this dressed-up wooden pallet.

Upholstery Club’s Shelly Leer

That is it! Isn’t she lovely? The completed upholstered ottoman adds softness to an industrial studio area, and can be completed by anyone with a couple added bucks plus a basic knowledge of sewing and woodworking (and I mean basic).

More: Build Your Own Wooden Deck Chair From a Pallet for $10

See related

203K FHA Problems

Many home buyers dream of buying a”fixer upper,” and calling it home. Unfortunately, many buyers do not have enough extra cash pay for repairs and to fund a house. The FHA 203k home loan rolls the cost of repairs, but also provides a way for buyers to purchase the job house down the street. The fix money is held after closing in escrow, and paid out as work is finished. Buyers should keep an eye out for troubles and some drawbacks, although this can seem like a great opportunity for visionaries.

Contractor Dissatisfaction

Borrowers should submit a repair plan and estimate of costs to the lender for approval prior to closing. This strategy may include cost and the kind of permits that are required, repairs, and a listing of contractors. HUD will permit the builders to start the work, once closing has happened on the house. Regrettably, if a homeowner is not happy with his performance or a contractor, a buyer following repairs have started to switch gears will not be allowed by HUD.

HUD Prerequisites

The 203K loan provides a borrower some cosmetics ones and likewise money for repairs. But repairs that are suggested are subject to HUD’s minimum property requirements, and this can conflict with buyers’ wishes. HUD requirements may contain upgrades such as even the replacement of heating and cooling systems , extra insulation in walls or ceilings, or setup of weatherstripping around doors and windows. Borrowers may have a pre-determined idea of how to budget the fix money, but you should be unaware that those plans may change.

Time Frame

After closing on the house, a buyer has in which to get the suggested work six months. Often, unforeseen obstacles can arise that delay or change the occupation but are not discovered before the remodel starts. Contractors may offer ideas for solving remodel issues that were unexpected. Unfortunately, this can cause major complications since if a change in the fix plan is needed, it can be exceedingly tricky to switch gears once the method is started.

Conflicts With Municipalities

Proposals that have been approved by HUD can conflict with county and city governments. Inspectors may need dis-allow a house alteration, or a different construction procedure completely. Additionally, local and zoning covenants and a plan that has taken a lengthy time to receive approved of by HUD can battle. Obtaining permits can delay the process which makes it difficult to fulfill the six-month deadline.

Delayed Closing

Is the whole procedure after closing complicated and lengthy, but getting to the closing table can be difficult. The normal house loan can take an average of 30 to 45 days. However, the complexity of the loan causes it take anywhere from 60 days to 90 days. If for some reason the loan does not close, a buyer has spent a lot of time that was wasted without the results.

See related

Differences Between Condo & Homeowner Insurance

Irrespective of the kind of home you own, you will typically need some sort of homeowner’s insurance to it, particularly in case you have a home mortgage. All homeowner’s insurance isn’t the same, though, and the kind you need depends on the kind of home you have. For instance, several differences exist between the condominium type of homeowner’s insurance and insurance for single-family dwellings.

Condominium Insurance

Condominium insurance typically addresses a condo owner’s specific non-communal property ownership requirements. Your personal condo insurance normally covers certain “walls-in” reduction, repair or replacement plus all of your private property. If you’re a condo owner, your condo association’s master insurance policy may cover everything from the home’s statues and walls outward. Your own condo insurance policy, though, might have to cover everything from the “unfinished walls-in,” including flooring and fixtures like carpeting.

Loss Assessments

Condominium insurance transported by condo owners can also be available with loss assessment coverage. Fundamentally, loss assessment coverage at a condo insurance policy insures the policyholder if her condo association levies fees on all owners to get funds to cover a reduction. Normally, condo association reduction assessments occur when associations suffer losses exceeding what their master insurance policies cover. As an instance, your condo association could assess you to help cover $10,000 of uncovered damage to your community’s building exteriors.

Shops Insurance

Conventional homeowners insurance like for single-family dwellings can be as comprehensive as simple as required as the mortgage lender may allow. Normal single-family homeowners insurance insures the whole structure plus all construction materials, including kitchen cabinets and other lasting elements. Most homeowners insurance also covers private property at 50 percent or greater of the worth of the insured home itself. Lastly, most traditional homeowners insurance covers other structures like detached garages and sheds.

Filing Claims

For most homeowners at single-family or similar homes, homeowner’s insurance claim filing is simple and made directly to insurers. If you’re a condominium owner looking at a claim, though, whether your own condo insurance or your association’s insurance pays depends upon the situation. Water damage caused by burst pipes to a condominium’s outer wall would most likely be paid by condo association insurance. Your condo insurance, though, may have to cover water damage caused by a burst kitchen sink pipe.

See related

Majestic Gas Stove Troubleshooting

A Majestic gas cooker provides an effective option if you want to heat a room in your home without turning on a heating apparatus. The brand offers a variety of models. But whatever kind of Majestic cooker you have, you might encounter difficulties from time to time, for example even the ignitor or odd smells during surgery. Even though you can resolve some of these issues yourself, don’t be afraid to telephone a service technician that is trained if you suspect problems beyond your skill level to troubleshoot and fix.

Pilot and Ignitor

Locate the pilot gathering for your version dependent on the operator’s manual. After the stove’s spark ignitor won’t produce a pilot flame, the electrode of the pilot could be faulty or misaligned. Eliminate the glass door before lighting the pilot. Check whether the control knob is set to the”Pilot” position. Hold a lighted match over the pilot orifice; turn it off and push the red ignitor button to engage the ignitor, when it lights. Measure the distance to confirm the gap between the electrode and pilot is 1/8 inch, which allows room to get a spark, if the pilot fails to light via the ignitor.

Defective Ignitor

If the ignitor itself is faulty, your cooker may fail to start. Put the control knob to the”Pilot” position, push it in all of the way in and hold it to test for a spark at the ignitor toward the pilot. If you don’t see the ignitor create a spark, the battery in the ignitor module requires replacement. Replace the whole ignitor module box, if the spark ignitor does not light after changing the battery.

Pilot Fails to Remain On

A thermocouple unit may keep the pilot light. Analyze it to confirm it is on the back of the valve. Air could be if the thermocouple is connected. Speak to your merchant because the gas line has to be bled with a repair expert to remove the air. If it does not have a sufficient gas distribution, your cooker may fail to remain on. Check for a complete tank, as important. The shutoff valve is available by verifying the red handle is directly in line with the gas line.

Burner Fails to Come On

After the stove pilot lights nice but the burner won’t light, the burner orifice might be clogged. Insert and remove a pipe cleaner in the orifice to clean it. The burner can neglect to light if the width of the burner orifice is too little, which keeps it from working. Speak with your dealer whether the diameter is a issue to find out if needed and replace. Confirm that the gas pressure for your cooker is low — contact the local gas company to have your gas link is examined by an experienced service person.

Strange Smells Throughout Operation

When your stove gives off odors it is generally a result of residue burn-off due to the production procedure. Open a window or vent the room until the smell is gone, and turn the cooker on high. It generally takes about six hours of constant use to eliminate the smell. Your cooker might also give off smells if it is burning vapors from paint, glue, hairspray, air fresheners or other household things in the air of the room. Adequately ventilate the room and do not use odor-producing goods while the cooker is on. If you smell gas when it’s turned off or once the oven is in operation, you might have a gas flow. Contact your local gas company immediately to locate and fix any leaks.

See related

The Way to Create a Lampshade Pendant Light

Brighten up a dark or dull room with an overhead pendant lighting custom-crafted from a lampshade. The project takes a little expertise with a glue gun and also the easiest of lamp-wiring abilities, but the result is an inexpensive and ceiling lighting that is one-of-a-kind and satisfying. Make one lamp to the dining room or a row of smaller pendants to line up over a kitchen island.

Cut fabric to fit around a plain drum lampshade with sufficient overlap at top and the base to fold across the rims so that you can glue it. You will overlap the side seam when gluing the fabric when the lighting is switched on however, the doubled cloth will show. So the two ends if at all possible, meet with no overlap Blend the side seam of the cloth to the lampshade precisely.

Hot glue the fabric to the exterior of the lampshade, folding the edges to the inside at bottom and the top and then gluing them. Cut a piece of grosgrain ribbon to glue around each of the bottom and top borders inside the lampshade at the rims, for a finish.

Remove the cord from the lamp kit from unscrewing and yanking the cable out of the canopy — the disc that covers the ceiling wiring and hole. Pull this cord up through the ring of this spider harp until the socket is flush with the harp. The lampshade will now dangle from the lamp fixture.

Re-thread the cord so that the ring will hang in the correct height and trim it. Secure the cable with the other hardware and the nut you eliminated to discharge it.

Before mounting the lamp, Switch off the power at the circuit breaker or fuse box. Enlist an experienced friend that will help you hire an electrician to hook it up safely, or hang and connect the ring. If you are confident you could manage the wiring that is simple, use a voltage checker to ensure that the power is off, then attach the mounting bracket and wires. The lamp kit will include directions. As you hold up the ring and fixture, A buddy on a ladder will do the connecting.

Twist the canopy correct the ring and screw in the correct wattage light bulb. Turn the power back on, flick the switch and revel in your new, bargain, pendant lamp that is decor-specific.

See related

The Way to Replace Window Cranks

Casement windows with opening mechanics are quite sturdy, but the cranks can strip over time and fail to work. In some cases, the crank is not the issue — the sash was painted closed on the exterior. If possible, inspect the outside of the window outside the home before replacing what appears to be a fold. Pull on the blade of a utility knife along the seam if the seam between the sash and the window jamb or sill is painted. Tools skills and some moderate effort are all you want to substitute it, if you decide that the crank is really the issue.

Turn the handle on the crank. If the fold will not turn, teeth or the splines on the little knob within the bottom of the deal are probably stripped. Pull the handle off the knob. Turn the knob knob with pliers or a small adjustable wrench to open the window.

Bushing in the end of the arm or adjust the window out or in by hand contrasts across the base of the window. Slip the wheel out of the track through the notch.

Eliminate any window trim if any trim exists that covers the surface of the fold. Some windows have a strip of timber covering the top of the fold, while other window cranks are seated atop the flat window stool or window jamb. Look, if your window has this kind of trim. Turn the screws counterclockwise with a horizontal or Phillips-head screwdriver to remove the trimming. If your trimming has no screws, then gently pry off the bar.

Turn the screws that fasten the fold to the window counterclockwise with a Phillips-head or horizontal screwdriver get rid of the fold.

Just take the old crank with you to purchase a replacement. Purchasing exactly the same size replacement is essential for proper functioning.

Fasten the crank to the window in the same spot at which you removed the old crank.

Adjust the window out or by hand to align bushing or the wheel in the arm’s end across the base of the window with the top notch from the track. Slip the wheel.

Set if you eliminated trim to get the fold the window trimming back in place. Turn the screws clockwise or tap on the finishing nails back in the window feces or jamb to reinstall the trimming.

See related